润滑油中磨损颗粒在线监测传感器研究进展*

油液监测是判断设备健康状况和提供设备故障隐患预警的有效方法。综述了用于监测润滑油中磨损颗粒的最新各类在线传感器的基本原理,包括批量磁吸附式传感器、微流体电容传感器、金属扫描传感器、双层平面线圈传感器、超声波传感器和光学传感器等,并讨论各种传感方法的优缺点以及未来发展面临的挑战;指出了高通量、高灵敏度、能区别金属与非金属磨粒、可采集磨粒图像信息的集成式传感器是未来研究的重点,集成式、智能化、无线传输的传感器是未来研发方向。     

纳米药物非临床药代动力学的研究策略及关注要点

随着纳米技术的迅速发展，纳米药物的研发已成为目前药物创新的发展方向之一。纳米药物具有基于纳米结构的尺度效应，其药代动力学特征与普通药物相比存在明显差异，其药代动力学研究与普通药物相比也有其特殊性。本文着重探讨纳米药物的非临床药代动力学的研究策略及关注要点，包括受试物、体内/外试验、生物样本分析、数据评价分析等，期望为研发者提供参考。     

0–1膨胀几何分布的客观贝叶斯分析

在医疗卫生、金融证券等应用领域，经常会同时出现零观测值、一观测值较多的情况. 为更好地拟合这类数据，提出0–1膨胀几何分布模型并进行客观贝叶斯分析. 通过参数变换，得到Jeffreys先验和reference先验. 设计后验分布的抽样算法，设置不同的样本量和参数真值，采用数值模拟方法对不同客观先验下的估计效果进行评估.     

Optical and electrical properties of ITO film on flexible fluorphlogopite substrate

Indium Tin Oxide (ITO) films were prepared, at room temperature, on a fluorphlogopite substrate using magnetron sputtering technology. At various temperatures of 500 °C, 600 °C, 700 °C, 800 °C, and 900 °C, the samples were (had) annealed for 2 h (a 2-h duration). The results showed improvement in the crystalline performance of ITO film at selected annealing temperatures, with a significant reduction in resistivity at 800 °C. The lowest resistivity is 4.08 × 10^?4 Ω-cm, which is nearly an order of magnitude lower than the unannealed sample. All samples have an average light transmittance above 85% in the visible light range (400–800 nm), and with increasing annealing temperature, the average light transmittance tends to decrease. Besides, at the sensitive wavelength of 550 nm, the light transmittance is as high as 93.74%. The sheet resistance testing of the sample was through the number of bending times, which revealed that with the increase of the number of bending, the sheet resistance increases. However, after 1200 bending times, the change rate of the sheet resistance remains below 5%. Thus, the ITO film prepared on the flexible fluorphlogopite substrate revealed excellent optical and electrical properties, good flexibility, and improved stability after high-temperature annealing, which guarantees successful application in flexible electronic devices.     

某特钢工业厂房办公楼结构设计

特钢工业厂房办公楼由2栋长90.6 m、宽34.2 m、高36.5 m的塔楼组成,两个塔楼之间2层设置钢平台,一端铰接,一端滑移.通过方案比选,两塔楼均采用钢框架(局部设支撑)结构体系,标准轴网为8.4 m×9.0m,结构布置基本对称,相邻处端部一跨存在斜柱.针对斜柱对结构的不利影响,对结构进行了 pushover分析,并采取了相应的措施;2层的钢平台跨度较大,进而做了舒适度分析,结果表明,满足规范的要求.     

2种侧围加强内框总成检具结构对比分析

概述了侧围加强内框总成与周边零件的匹配关系,从检具操作的人机工程出发,描述了侧围加强内框总成检具的2种定位方式和结构设计,对比了2种定位方式对于检测结果的影响,总结了其优点和弊端,结果表明侧围加强内框总成检具采用车内方向朝下的定位方式效果更好。     

汽车安全带固定点失效分析及结构优化

以乘用车后排安全带固定点为对象，基于安全带固定点强度试验结果，通过有限元方法建立模型，简化并调试有限元模型，进行试验对标分析。经过对标后，有限元分析结果与试验结果基本吻合。然后基于对标后的有限元模型对结构进行优化，提高安全带固定点强度，提出优化方案，并通过试验验证，满足法规要求。通过利用CAE分析技术在产品开发过程中的应用，有效找到问题原因并有针对性地加以优化，从而缩短开发周期和节约成本。     

Simultaneous improvement of thermal conductivity and mechanical properties for mechanically mixed ABS/h-BN composites by using small amounts of hyperbranched polymer additives

Recently, thermal interface materials (TIMs) are in great demands for modern electronics. For mechanically mixed polymer composite TIMs, the thermal conductivity and the mechanical properties are generally lower than expected values due to the sharply increased viscosity and poor filler dispersion. This work shows that addition of a small amount of polyester-based hyperbranched polymer (HBP) avoided the trade-off in mechanically mixed ABS/hexagonal boron nitride (h-BN) composites. After adding 0.5 wt% HBP, the maximum h-BN content in the composites increased from 50 to 60 wt%. The out-of-plane, in-plane thermal conductivity, and tensile strength of ABS/h-BN with 50 wt% h-BN were 0.408, 0.517 W/mK, and 18 MPa, respectively, and were increased to 0.729, 0.847 W/mK, and 32 MPa by adding 0.5 wt% HBP, while 0.972, 1.12 W/mK, and 29.5 MPa were achieved for ABS/h-BN/HBP with 60 wt% h-BN. The morphological and rheological results proved that these enhancements are due to the improved h-BN dispersion by decreasing viscosity of composites during mixing. Theoretical modeling based on the modified effective medium theory confirmed such results and showed that the interfacial thermal resistance also decreased slightly. Thus, this work demonstrates a facile and scalable method for simultaneously improving the thermal conductivity and mechanical properties of thermoplastic-based TIMs.     

胡海陶瓷艺术作品选登

正~~     

钢渣热焖工艺及其对水泥性能的影响

本文研究了不同的热焖压力和时间对钢渣活性的影响和钢渣的不同掺量对水泥性能的影响.热焖工艺主要改善的是钢渣的膨胀性,熟料的7 d膨胀率为0.034％,未热焖的钢渣掺入15％和35％时膨胀率分别增加155.9％和311.8％,而1 MPa 1 h热焖后,相比于未热焖的情况,钢渣掺入15％和35％时分别降低77.0％、89.3％,钢渣掺量25％时,其3 d、7 d、28 d 抗压强度分别增加8. 0 MPa、3.6 MPa、2.7 Mpa,分别提高21.1％ 、11. 3％ 、6. 1％.